Painting the Hull and Brightwork

The hull has finally been painted and so has the bright work! I will say that it was a lot simpler affair to paint the hull than the deck and for the most part it turned out OK. A little practice with the 2 part paint along with a lack of nooks and crannies made this a much better experience!

For the bright work I decided to go with CETOL since I am under the impression that is a bit more robust than varnish. I also went with a gloss finish!

Still a couple of painting tasks left to finish: Non Skids and the Foils!

Painting the Upper Deck

Finally started painting the boat! It has been a task I have not been looking forward to based on all the nooks and crannies within the cross members that needed to be painted. It is also a first time for using Interlux Perfection which is a two part paint.

Interlux recommended two coats, I ended up with three for a couple of reasons. Firstly I had the paint and secondly, long term, it would be more durable.

My experience with this paint was OK. First of all it would have gone better if I had sprayed it on. Unfortunately I do not think my neighbors would have been very happy if I atomized a bunch of highly toxic paint / thinners next to their homes so even though I have the equipment I decided to do the old roll and tip.

The other issue is painting large surfaces in a garage. You need to have good ventilation which allows dust particles, and small insects to land in your setting paint so it is impossible to get a perfect surface. Finally, there is the learning curve of using a new type of paint that sets up quickly and does not allow you to brush over a spot if it didn't turn out 100% without ruining the finish.

All being said the finish on the deck looks good for being painted on and for a boat that will be used is good enough!

Drilling holes in the hull!

Next step on the rudder is to mount it to the transom. While I was at it it went ahead and drilled the twin drains at the back.

It is worth noting that I drilled the drain holes first and then I mounted the rudder. Interestingly enough after I looked at Dudley's instruction it may have been wiser to mount the rudder first then drill the holes! Good news is that the height worked out good and also that the drain holes are at the absolute lowest point the hull!

While I was at it I also cut the inspection hole in the front of the deck and widened out the hole at the rudder mount area to install the access plate. I was going to buy a hole saw to do it but decided to just free hand it with a jig saw.

On all these holes I went back and added epoxy to the exposed wood to seal them from moisture.

Rudder Inspection Port

Front Inspection Port

I Also decided to mount some of the hardware on the bowsprit and mast extension. 

So next steps is to get the hull / deck painted. Prior to getting too carried away I wanted to make sure that I had a good way to get the hull up and down off the ceiling without any "strap rash" Therefore, after a little research I went ahead and bought a Harken Hoister. Works pretty slick!

Finishing up the Rudder

Ok, so I have been absent from my boat for quite a while. A second move to Orange County  California and the purchase of a new (to me) Beneteau F235 has put this project on hold for too long.  My goal now is to get this boat on the water this summer!

A few months ago I decided to at least tackle one of the smaller projects which was finishing the rudder.

A few things had to happen:

First of all I had to apply the finish to it. Previously I had put a couple of coats of laminating epoxy. So I sanded it smooth and applied a couple of coats of rub on polyurethane. It is one of my favorite easy finishes and I didnt want to hassel with varnish with all the nooks and cranies.

I attached the gudgeons to the rudder and used a phillips screw driver to make sure they were somewhat lined up

Next step was to attach the Ronstan Battlestick that I bought as a tiller extension

I ended up having an old neoprene diving "bootie" that was past its prime so I cut it up into strips and use 3M 4200 adhesive to glue it into place to hold the rudder straight in the "Cassette"

Not the prettiest solution but it should work fine. With that I would call this particular part done!